Documentation: DeltaScrollSaw-40-601 manual Make/Model: Delta Scroll Saw Model 40-601 S/N: 80C07455 Location: Workshop Overview A scroll saw has a short, reciprocating blade. It can cut curves, including very small radius turns with small enough blades. It has a broad round table to support your work in all orientations. The blade can be easily removed, which …
Category: Workshop
AMT443 Wen Oscillating Belt & Spindle Sander
Overview Make/Model: Wen Oscillating Belt & Spindle Sander / 6524 Serial Number: 127304-00046 Documentation: Full Manual Sanding belt size is 4″ x 24″: Amazon Link Sanding drums are 4 1/2″ x (1/2″, 3/4″, 1″, 1 1/2″, 2″): Amazon Link The sander is set up near the shop entrance and uses the bench connection to AMT255 …
AMT442 Delta Unisaw
Documentation Manual PDF (Note this is for very similar model 36-801) Make/Model: Delta Unisaw 36-802 Location: Workshop Table Saw Basic Rules Only use the table saw if you are properly trained to do so and have taken Ace’s certification class. Wear eye protection. No freehand cuts! Use the fence for rip cuts. Use the miter …
AMT441 Ridgid 4 Gal Shop Vac
RIDGID 4 Gallon 5.0 Peak HP Portable Shop Vacuum This shop vac is intended to be used with the dust separator, which gets attached to the router table or power sanders. In fact, any shop vac can be used with the dust separator, but this shop vac is small enough to fit under the router …
AMT440 Delta Bandsaw Model 52-963
Online Manual: https://www.mikestools.com/download/Delta-Bandsaw-manuals/28-203.pdf (maybe) Download cached version: Delta 28-203 Manual (maybe) Another page about it: http://www.vintagemachinery.org/photoindex/detail.aspx?id=43960 SPECIFICATIONS: Motor: 3/4 HP dual voltage motor set to 115v 11 1/2″ resaw capacity Carter bearing guides top and bottom Max realistic blade size: 1/2″ Max. cutting height (resaw capacity): 3-5/8″ Blade guides: Ball-bearing upper and lower Table size: Table …
3D Printed Workshop Supplies
Some parts and supplies in the workshop are 3D printed. This page contains all of them. Laguna Bandsaw Dust Deflector Insert The Laguna bandsaw (AMT399) has a plastic insert just under the table. It crosses the blade and deflects sawdust toward the dust collection port. It’s an important part because it helps prevent sawdust from …
AMT438 Wen Variable Speed 6″ bench grinder
Serial Number: 12490300297 The Wen Variable Speed bench grinder is part of the workshop’s dedicated sharpening station. The left wheel is only for hollow grinding flat blades like chisels and planes. The right wheel is for sharpening other blades. The grinder should always be used at the lowest speed. Here is a video covering the …
Writing Instruments
To replenish chalk, pencils, sharpies and dry erase pens, take some from the supply workshop closet next to the planer. Look for a box with a blue label with the Three Star Icon. Take what is needed and put it where you were hoping to find some. Thanks! If the main supply is out of …
Blue Tape
To replenish blue tape, take some from the supply workshop closet next to the planer. Look for a box with a blue label with the Three Star Icon. Take a new roll from the labeled box and put it where you were hoping to find some. Thanks! If the main supply is empty, or nearly …
Hearing Protection
In-Ear Hearing Protection To replenish in-the-ear hearing protection units, take some from the supply in the storage area in the same room as metal, right next to the member storage shelves. Look for a box with a blue label with the Three Star Icon. Take a several pair from the supply box and put them …